소개
With the widespread promotion of LED applications, the requirements for its reliability are becoming higher and higher. The LED reliability test is to evaluate the stability and reliability of the product in a specific environment and use conditions. For LED products, we mainly focus on the lamp bead life, heat resistance, light decay, impact resistance and environmental adaptability and other indicators of the test and evaluation.
LED 제품 또는 구성 요소는 염수 분무 테스트를 수행해야 합니까? [일반적으로 염수 분무 또는 작업 환경의 부식 위험이 있는 제품 또는 구성 요소에만 해당]
금속과 그 합금
B 주석 도금 니켈 도금과 같은 금속 코팅
C 스프레이와 같은 유기 코팅
D: 양극 산화막
Under salt fog chamber that we usually refer to relevant national and industry standards to ensure the accuracy and comparability of test results. for example:
GB/T 10125, ISO 9227 인공 대기 부식 시험 염수 분무 부식
ASTM B117 미국 표준 염수 분무 시험
GB/T 2423.17, 전자 제품에 대한 IEC 60068-2-11 염수 분무 시험
GB/T 2423.18, IEC 60068-2-52 전자 교대 염수 분무 시험
Salt spray test: the LED sample is exposed to salt spray environment, simulate the use scenario in the Marine environment, by observing the change of its surface corrosion, electrical performance changes and other indicators, to evaluate its reliability in a strong corrosion environment.
인공 시뮬레이션 염수 분무 시험 분류:
(1) Neutral salt spray test (NSS test)
It is the earliest and most widely used accelerated corrosion test method. It uses 5% sodium chloride brine solution, the PH value of the solution is adjusted in the neutral range (6.5~7.2) as a spray solution. The test temperature is set at 35℃, and the settlement rate of salt spray is required to be between 1-2ml/80cm2(h).
【 Neutral salt spray test is the most commonly used test method. If no special instructions are made, the salt spray test we talk about usually refers to the neutral salt spray test 】
(JOEO labroom의 염수 챔버를 사용한 통 스프레이 테스트)
(2) Acetate spray test (ASS test)
It is developed on the basis of the neutral salt spray test.
It is to add some glacial acetic acid in 5% sodium chloride solution, so that the PH value of the solution is reduced to about 3.1-3.3, the solution becomes acidic, and the salt spray finally formed is also from the neutral salt spray into acid.
(3) Copper accelerated acetate spray test (CASS test)
It is a rapid salt spray corrosion test recently developed abroad. The test temperature is 50℃, and a small amount of copper salt - copper chloride is added to the salt solution to strongly induce corrosion.
(LED 칩 염수 분무 시험)
(4) Alternating salt spray testIs a comprehensive salt spray test
It is actually a neutral salt spray test plus constant wet heat test.
It is mainly used for cavity type machine products, through the penetration of tidal environment, so that salt spray corrosion is not only produced on the surface of the product, but also produced inside the product. It is the alternating conversion of the product in the salt spray and wet and hot two environmental conditions, and the final examination of the electrical and mechanical properties of the whole machine product.
(염무 챔버가 있는 JOEO 실험실의 가로등 염수 분무 테스트)
모델 | 소금 안개 챔버 | 재질 보기 STH - 90 | 재질 보기 STH-100 | 재질 보기 STH-120 | 재질 보기 STH-160 | 재질 보기 STH-135 | 재질 보기 STH-200 | 재질 보기 STH-210 |
내부 치수 WxHxD (mm) | 900x600x500 | 1000x700x600 | 1200x800x500 | 1600x1000x500 | 1350x850x1200년 | 2000x1200x600 | 2100×950×1250 | |
외형 치수 WxHxD (mm) | 1500x1300x1000년 | 1560x1000x1350 | 1900x1100x1400년 | 2300x1300x1400 | 2160x1200x1450 | 2700x1500x1500 | 2711×1150×1970 | |
용량 (L) | 270 | 430 | 480 | 800 | 1377 | 1440 | 2500 | |
테스트 표준 | ACSS, 담그다, 드라이에어, 휴미, 룸에어 | |||||||
온도 범위 | A: RT(+15°C) ~ +85°C B: -10°C ~ +85°C C: -20°C ~ +85°C D: -40°C ~ +85°C E: - 55°C ~ +85°C | |||||||
습도 범위 | 20% ~98% 영국 고지 연대 (온도 RT{+15°C} ~ 80°C), 15%~95% 영국 고지 연대는 제습기 또는 건조기를 추가합니다 | |||||||
온도 상승/ 떨어지는 속도 비율 | 온도 상승 약 : 0.1 ~ 3.0 °C / min (3-10 °C / min 전체 코스 평균 - 선택 사항) 약 떨어지는 온도 : 0.3-1.0 °C / min (3-10 °C / min 전체 코스 평균 - 선택 사항) | |||||||
분석 정확도/ 분포 : 온도 및 습도의 균일 성 | 0.1°C ; 0.1% 상대습도 ± 2.0 °C; ±5% 영국 고지 연대 | |||||||
온도의 제어 정확도 | ±0.5°C ±2.5°C 2%R.H | |||||||
압력 버킷 온도 | 식염수 시험 방법(NSS, ACSS) 47±1°C; 부식 테스트 (CASS)63±1°C | |||||||
압축 공기 압력(KGf) | 1.0-6.0 | |||||||
분무량 | 1.0-2.0ml/80cm²/h(최소 16시간 작업 및 평균값 취) | |||||||
압축기 | 프랑스 "Tecumseh" 상표, 독일 "Bitzer" 상표 또는 samilar 상표 | |||||||
선택적인 부속품 | 견본 선반, 손수레 등 | |||||||
스프레이 방법 | 연속 스프레이 또는 프로그래밍 가능한 스프레이 | |||||||
힘 | AC220V: 1phase3 라인 50/60Hz AC380V: 3 단계 5 선 50/60Hz |